« previous next »
Pages: [1]   Go Down

Author Topic: 1964 1/2 square end sill plates  (Read 2261 times)

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1207
  • There is no end to doing right. Giddyup!!!
1964 1/2 square end sill plates
« on: February 22, 2014, 10:59:08 AM »
Does anyone know when the early square end sill plates were changed over to the rounded end 65-66 type? Is anyone reproducing the square end sill plates?
Logged
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'

Offline kutzoh

  • Gold Level Subscriber
  • Full Member
  • *****
  • Posts: 220
Re: 1964 1/2 square end sill plates
« Reply #1 on: February 22, 2014, 12:28:17 PM »
Don't know the date, whenever they ran out of stock. I had a Dec. '64 coupe parts car that had one square corner sill and one rounded corner sill. As far as I know, no one is reproducing the square corner. I picked up a "better" set of square corner sills than my originals and am having them cleaned, striped and re-anodized.

Greg
Logged
64.5 Dearborn coupe, D-Code, June 28, 1964   Skylight Blue

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24628
Re: 1964 1/2 square end sill plates
« Reply #2 on: February 22, 2014, 12:48:09 PM »
Quote from: Hipo giddyup on February 22, 2014, 10:59:08 AM
Does anyone know when the early square end sill plates were changed over to the rounded end 65-66 type? Is anyone reproducing the square end sill plates?

Since the usage is not dependent on other parts or processes like the generator change over, the point where the change over is likely different depending on what plant your asking about ;)

If we had that at least we could look for a pattern rather than looking at all the plants.
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1207
  • There is no end to doing right. Giddyup!!!
Re: 1964 1/2 square end sill plates
« Reply #3 on: February 22, 2014, 02:22:06 PM »
This would be relating to the Dearborn assembly plant. My car is a June built 64 1/2. Thanks
Logged
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'

Offline mgmradio

  • Global Moderator
  • Sr. Member
  • ****
  • Posts: 310
Re: 1964 1/2 square end sill plates
« Reply #4 on: February 22, 2014, 04:04:49 PM »
A June 64 built Dearborn car would have had the square cornered sill plates. My 4500 mile Aug built car has them.
Logged
Formerly the MCA ANHJ 64.5-66!

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24628
Re: 1964 1/2 square end sill plates
« Reply #5 on: February 22, 2014, 07:19:30 PM »
Quote from: Hipo giddyup on February 22, 2014, 02:22:06 PM
This would be relating to the Dearborn assembly plant. My car is a June built 64 1/2. Thanks

Great that narrows it down allot ;)

Haven't tracked this detail on my spread sheets like I have for San Jose but looking through my picture the change appears to have taken place between car 631036 (highest assigned VIN I found with square corners) and 675924 (lowest assigned VIN with the rounded corners that appears to be original to the car.  Plenty of earlier cars that had carpet changed and rounded corner sill plates but those stood out in the pattern that developed

So approx Mid Feb into March at this point. San Jose change over by contrast was earlier it appears


Hope this helps
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline ChrisV289

  • Hero Member
  • *****
  • Posts: 1965
Re: 1964 1/2 square end sill plates
« Reply #6 on: February 22, 2014, 08:36:23 PM »
Jeff,

When was the change over for San Jose?

Chris
Logged
Chris
1965 Honey Gold Fastback (SJ 10/29/64)
1965 Caspian Blue Fastback (SJ 06/03/65)
2009 V6 Mustang Coupe

Offline CW4macret

  • Sr. Member
  • ****
  • Posts: 399
Re: 1964 1/2 square end sill plates
« Reply #7 on: February 22, 2014, 11:47:15 PM »
My is a Detroit build with square.
Logged
Mac
64.5, 5F07D
66 Convertible 6T08T
71 Mach1 429CJ 1F05J
01 Coupe
05 GT
08 GT500
14 GT500

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24628
Re: 1964 1/2 square end sill plates
« Reply #8 on: February 24, 2014, 01:16:22 AM »
Quote from: ChrisV289 on February 22, 2014, 08:36:23 PM
When was the change over for San Jose?

Best I can figure from examples the change over took place between the assembly of car #175262 and car #180051
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)
Pages: [1]   Go Up
« previous next »