« previous next »
Pages: [1]   Go Down

Author Topic: A/C underdash Unit  (Read 2081 times)

Offline bryancobb

  • Silver Level Subscriber
  • Hero Member
  • ****
  • Posts: 1077
  • 2009 Ridn' Around
A/C underdash Unit
« on: November 13, 2010, 01:51:15 PM »
Does anyone have a coule of pictures of the decals on the upper surfaces of the A/C evaporator blower housing.  One of them looks to be large red letters that is some kind of ATENTION NOTE.  The other one is small black lettering and stamping with the date and charging information

I cannot make out mine, and I want to recreate them.
Logged
66 Metuch Conv
Nightmist, Std Blu Int
6T08C223904    76A       K         22       15c     21      6        6
                      BODY  COLOR   TRIM    DATE   DSO   AXLE  XMSN
   C/O  785                                   (rotation #)
   16    C14   6T08C223904        (weld bay 16, bucked MAR 14)

Offline 5F09CNot4Sale

  • Full Member
  • ***
  • Posts: 195
  • If it does not fit, you need a bigger hammer!
Re: A/C underdash Unit
« Reply #1 on: November 13, 2010, 03:18:15 PM »
I am still in the middle of a move but I have a unit with stickers still on it. Will do my best to photo them and post.
Logged
5F09C3031XX Sept 28 64 Dearborn
5F07F1838XX June 29 64 Dearborn

Offline bryancobb

  • Silver Level Subscriber
  • Hero Member
  • ****
  • Posts: 1077
  • 2009 Ridn' Around
Re: A/C underdash Unit
« Reply #2 on: November 13, 2010, 07:33:44 PM »
Thanks a lot in advance.
Lookin forward to getting them.
Just email them to me at bryan@llind.com
Logged
66 Metuch Conv
Nightmist, Std Blu Int
6T08C223904    76A       K         22       15c     21      6        6
                      BODY  COLOR   TRIM    DATE   DSO   AXLE  XMSN
   C/O  785                                   (rotation #)
   16    C14   6T08C223904        (weld bay 16, bucked MAR 14)

Offline bryancobb

  • Silver Level Subscriber
  • Hero Member
  • ****
  • Posts: 1077
  • 2009 Ridn' Around
Re: A/C underdash Unit
« Reply #3 on: December 17, 2010, 09:06:46 PM »
On a March 66 Metuchen car...  The underdash evap unit has a threaded rod at the back that acts like a "kickstand" to support the rear of the unit at the right height.

Q:  Didn't I see somewhere where the bttom of this threaded rod has a nut on the bottom of it to distibute the load.  If I remember right, it was a seat to floor attaching nut that holds the seats in.  Is this correct?
Logged
66 Metuch Conv
Nightmist, Std Blu Int
6T08C223904    76A       K         22       15c     21      6        6
                      BODY  COLOR   TRIM    DATE   DSO   AXLE  XMSN
   C/O  785                                   (rotation #)
   16    C14   6T08C223904        (weld bay 16, bucked MAR 14)

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7686
Re: A/C underdash Unit
« Reply #4 on: December 17, 2010, 09:29:22 PM »
I always thought the nut was to lock the rod in place once adjusted.
Logged
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin

Offline bryancobb

  • Silver Level Subscriber
  • Hero Member
  • ****
  • Posts: 1077
  • 2009 Ridn' Around
Re: A/C underdash Unit
« Reply #5 on: December 18, 2010, 02:47:39 PM »
Well Charles,
After looking at my Osborne book, you are right.  The picture I saw,
I guess, was one where somebody had just put one of those seat nuts on upside down to push down on the carpet.

It just looked like it made sense for it to be there.

The threaded rod is tapered to a rounded point that looks like it mau penetrate the carpet after a few hundred pot-holes.
Logged
66 Metuch Conv
Nightmist, Std Blu Int
6T08C223904    76A       K         22       15c     21      6        6
                      BODY  COLOR   TRIM    DATE   DSO   AXLE  XMSN
   C/O  785                                   (rotation #)
   16    C14   6T08C223904        (weld bay 16, bucked MAR 14)
Pages: [1]   Go Up
« previous next »