« previous next »
Pages: [1]   Go Down

Author Topic: Air Extractor Assembly nuts  (Read 1328 times)

Offline 65Ford

  • Jr. Member
  • **
  • Posts: 77
Air Extractor Assembly nuts
« on: March 04, 2017, 01:27:03 AM »
Two questions:

1.  Are these two nuts correct for an October 2 '64 San Jose fastback air extractor assembly?

2.  If correct nuts,  how and where may I procure a bunch (14 of the one piece style and 8 of the two piece)?

Thanks!

Logged
63A  R  28  02K  51  1  5
5R09A142

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7346
Re: Air Extractor Assembly nuts
« Reply #1 on: March 04, 2017, 12:00:21 PM »
A quick answer, not available. Look in the library under Mustang Hardware Spreadsheet 64-66.,
Jim
« Last Edit: March 05, 2017, 02:14:11 PM by jwc66k »
Logged
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline ChrisV289

  • Hero Member
  • *****
  • Posts: 1965
Re: Air Extractor Assembly nuts
« Reply #2 on: March 05, 2017, 02:05:59 PM »
AMK doesn't sell these under "nuts - stamped machine thread" for the one on the left?  There are several from page 69-71 but I don't know what the dimensions are to provide a part #
Logged
Chris
1965 Honey Gold Fastback (SJ 10/29/64)
1965 Caspian Blue Fastback (SJ 06/03/65)
2009 V6 Mustang Coupe

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7346
Re: Air Extractor Assembly nuts
« Reply #3 on: March 05, 2017, 02:13:56 PM »
Quote from: ChrisV289 on March 05, 2017, 02:05:59 PM
AMK doesn't sell these under "nuts - stamped machine thread" for the one on the left?  There are several from page 69-71 but I don't know what the dimensions are to provide a part #
Quote from: jwc66k on March 04, 2017, 12:00:21 PM
Look in the library under Mustang Hardware Spreadsheet 64-66.,
Please do your homework.
Jim
Logged
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline 65Ford

  • Jr. Member
  • **
  • Posts: 77
Re: Air Extractor Assembly nuts
« Reply #4 on: March 05, 2017, 02:45:28 PM »
Jim,

Thank you for sharing the Mustang Hardware spreadsheets - they're quite handy and shows a lot of work went into them.

I noticed the '65s had a count of 28 flat stamped nuts but '66 had 20.  I didn't think the '65s had more unless they double nutted the baffles?

At any rate, it seems the going rate for air extractor assemblies on Craigslist in California is $500 for beat up incomplete units - ouch.
Logged
63A  R  28  02K  51  1  5
5R09A142

Offline 65Ford

  • Jr. Member
  • **
  • Posts: 77
Re: Air Extractor Assembly nuts
« Reply #5 on: March 05, 2017, 06:42:16 PM »
I just found this while hunting for the air extractor assemblies I found the following hardware kit from CJ Pony Parts:

  Part Number F-2934 

It looks close enough for the daily driver.  Much better than what I was facing which was raiding the bins at Home Depot...
Logged
63A  R  28  02K  51  1  5
5R09A142

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7346
Re: Air Extractor Assembly nuts
« Reply #6 on: March 05, 2017, 06:54:59 PM »
Quote from: 65Ford on March 05, 2017, 06:42:16 PM
I just found this while hunting for the air extractor assemblies I found the following hardware kit from CJ Pony Parts:

  Part Number F-2934 
It looks close enough for the daily driver.  Much better than what I was facing which was raiding the bins at Home Depot...
The CJ kit is actually an AMK kit (52 pieces, $24), and I forgot about the AMK kit. I do remember that there was a difference in the nuts in the AMK kit, washer diameter I think. For a driver, it may be exactly what you need.
Jim
Logged
I promise to be politically correct in all my posts to keep the BBBB from vociferating.
Pages: [1]   Go Up
« previous next »