Author Topic: Driveshaft Paint Markings - 66 C code Automatic Application  (Read 6151 times)

Offline Building 3

  • Sr. Member
  • ****
  • Posts: 353
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #15 on: May 22, 2016, 02:11:17 PM »
Here is a photo
1966 289 C code auto convertible December 1965 scheduled build at Dearborn.

1966 289 C code auto convertible
October 1965 scheduled build at Metuchen.

Offline Building 3

  • Sr. Member
  • ****
  • Posts: 353
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #16 on: May 24, 2016, 12:50:52 PM »
A good paint match to the forward stripe ( the pink/lilac/lavender stripe) is Sherwin-Williams Wisteria SW 6822 181-C3.
1966 289 C code auto convertible December 1965 scheduled build at Dearborn.

1966 289 C code auto convertible
October 1965 scheduled build at Metuchen.

Offline Building 3

  • Sr. Member
  • ****
  • Posts: 353
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #17 on: June 08, 2016, 03:43:30 PM »
Here's the restored driveshaft for the 1966 C-Code automatic. The stripes are 15/16" each and are 5-1/2" apart.
1966 289 C code auto convertible December 1965 scheduled build at Dearborn.

1966 289 C code auto convertible
October 1965 scheduled build at Metuchen.

Offline carlite65

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 2410
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #18 on: June 08, 2016, 03:46:45 PM »
did you tape them off? the edges look a little neater than i would expect to see.
5F09C331248

Offline Building 3

  • Sr. Member
  • ****
  • Posts: 353
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #19 on: June 08, 2016, 04:34:42 PM »
Yes, on the original unrestored, the edges are perfect.  They measured exactly 15/16" all the way around the driveshaft.  That is first photo in this thread. Up close, they look mechanically applied, or someone with a very steady hand.  That driveshaft has not been out of the car, the U-joints are original, as are the differential, trans, and engine. 25,000 miles. (The diff is making noise but I don't want to disturb anything especially given the amount of miles that I drive a year.)
1966 289 C code auto convertible December 1965 scheduled build at Dearborn.

1966 289 C code auto convertible
October 1965 scheduled build at Metuchen.

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7344
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #20 on: June 08, 2016, 07:38:56 PM »
did you tape them off? the edges look a little neater than i would expect to see.
Agree.
Yes, on the original unrestored, the edges are perfect.  They measured exactly 15/16" all the way around the driveshaft.  That is first photo in this thread. Up close, they look mechanically applied, or someone with a very steady hand. 
With the lines that go around the shaft in the original photo I would be inclined to believe the shaft was rolled with the brush held steady. No masking was used. This is a production line, done quickly is the preferred method, not artistic.
Jim
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline SamG

  • Newbie
  • *
  • Posts: 18
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #21 on: June 15, 2016, 10:34:11 PM »
Mine matches Phill's

66 C code Automatic...Don't have the other vitals close


Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7344
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #22 on: June 16, 2016, 12:13:55 AM »
Remember, that number, 19078-4(something) is the stock number of the tube's manufacturer and was stamped every 10 feet or so. That's why some drive shafts have it, and others do not.
Jim
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24606
Re: Driveshaft Paint Markings - 66 C code Automatic Application
« Reply #23 on: June 20, 2016, 04:52:13 PM »
Mine matches Phill's

Tubes  (where the number came from) appear to have been done in batches from the supplier so you should find allot of matched with the few dates (last two digits) that are commonly found
Jeff Speegle

Anything worth doing is worth doing concours ;)