« previous next »
Pages: [1]   Go Down

Author Topic: 70 - Firewall clamp for wire harness at Blower Motor  (Read 1592 times)

Offline blackjadeboss

  • Newbie
  • *
  • Posts: 33
70 - Firewall clamp for wire harness at Blower Motor
« on: July 20, 2015, 08:03:41 PM »
I am looking for a source for the rubber coated J clamp that held the wire harness for the alternator, voltage regulator and starter solenoid.

It attached to the outer top blower motor stud.

Has anyone sourced that new ?

Thanks in advance.

Keith
« Last Edit: July 21, 2015, 02:27:38 PM by J_Speegle »
Logged

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24625
Re: Firewall clamp for wire harness
« Reply #1 on: July 21, 2015, 12:01:40 AM »
What year?
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline blackjadeboss

  • Newbie
  • *
  • Posts: 33
Re: Firewall clamp for wire harness
« Reply #2 on: July 21, 2015, 07:41:26 AM »
It's a 70, and in fact I should have posted this in the Boss, or Dearborn section.

My bad.
Logged

Offline rockhouse66

  • Hero Member
  • *****
  • Posts: 946
Re: Firewall clamp for wire harness
« Reply #3 on: July 21, 2015, 08:47:25 AM »
This is the clamp you are looking for?  I see this routing on most Dearborn cars but some are clipped under the brace like is common on a Metuchen car.

Logged
Jim
'66 GT FB

Offline blackjadeboss

  • Newbie
  • *
  • Posts: 33
Re: Firewall clamp for wire harness
« Reply #4 on: July 21, 2015, 11:11:19 AM »
Indeed it is!
Logged

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24625
Re: 70 - Firewall clamp for wire harness at Blower Motor
« Reply #5 on: July 21, 2015, 02:28:26 PM »
Just picked them up at wrecking yards or made them from scratch. Believe they are the same as the ones used for the AC vacuum lines normally directly above on AC cars (another source)

Fix the title to represent what you were asking about ;)
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline blackjadeboss

  • Newbie
  • *
  • Posts: 33
Re: 70 - Firewall clamp for wire harness at Blower Motor
« Reply #6 on: July 21, 2015, 02:46:44 PM »
Thanks Jeff.
Logged

Offline specialed

  • Hero Member
  • *****
  • Posts: 1095
Re: 70 - Firewall clamp for wire harness at Blower Motor
« Reply #7 on: July 22, 2015, 10:29:03 AM »
the a/c line strap holder is smaller  but you can find that size strap holder under dash wiring harness.
Logged

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24625
Re: 70 - Firewall clamp for wire harness at Blower Motor
« Reply #8 on: July 22, 2015, 02:43:59 PM »
Quote from: specialed on July 22, 2015, 10:29:03 AM
the a/c line strap holder is smaller  but you can find that size strap holder under dash wiring harness.

The heater motor one is that wide??  Thanks for the correction for the OP
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline blackjadeboss

  • Newbie
  • *
  • Posts: 33
Re: 70 - Firewall clamp for wire harness at Blower Motor
« Reply #9 on: July 22, 2015, 02:59:48 PM »
I have both ... so I can measure. My original f/w piece is pretty ugly.
Logged
Pages: [1]   Go Up
« previous next »