« previous next »
Pages: [1]   Go Down

Author Topic: Correct tie rod sleeves  (Read 1732 times)

Offline Ldouble619

  • Newbie
  • *
  • Posts: 29
Correct tie rod sleeves
« on: May 30, 2021, 10:17:18 PM »
Does anyone make a correct tie rod sleeve.  Seen some online that are close with the wrong nuts and bolts.

Clean up the originals?
Logged

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 9362
Re: Correct tie rod sleeves
« Reply #1 on: May 30, 2021, 10:46:36 PM »
Quote from: Ldouble619 on May 30, 2021, 10:17:18 PM
Does anyone make a correct tie rod sleeve.  Seen some online that are close with the wrong nuts and bolts.

Clean up the originals?
There are some close looking repro's sleeves but they are too long. No one I am aware makes a correct tie rod sleeve let alone the nuts ,bolts and clamps. The nuts ,bolts and clamps are relative easy to find in good enough condition to restore . The sleeves on the other hand are much harder to find that are nice enough to restore. Wrench marks and pits are the typical problems.
Logged
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby

Offline Ldouble619

  • Newbie
  • *
  • Posts: 29
Re: Correct tie rod sleeves
« Reply #2 on: May 31, 2021, 12:46:19 AM »
Thanks. I?ll start cleaning my up.
Logged

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7346
Re: Correct tie rod sleeves
« Reply #3 on: May 31, 2021, 01:22:07 AM »
Those same sleeves were used on a number of Ford products. Go to the library and locate "Ford Car Parts" (aka MPC) and look up base number 3310 in the steering section.
Jim
Logged
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline SCJSTU

  • Sr. Member
  • ****
  • Posts: 272
Re: Correct tie rod sleeves
« Reply #4 on: July 18, 2021, 10:31:05 PM »
Bringing this post back up???anyone have pictures of original ones on a car?

Jan built 351W
Logged
1969 Shelby GT350 convertible  4spd-AC built 1-27-69
1967 Mustang S-Code 4-speed built Jan 1967 non therm
1956 Ford F100 Big Window 392 Hemi

1961 Falcon 2 Door Station Wagon 302V8
2004 Mach 1 Azure Blue

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 9362
Re: Correct tie rod sleeves
« Reply #5 on: July 18, 2021, 10:43:05 PM »
Quote from: SCJSTU on July 18, 2021, 10:31:05 PM
Bringing this post back up???anyone have pictures of original ones on a car?

Jan built 351W
Same sleeves used 65-70 V8 . Later versions and replacements were contoured down the length.  Pictures on unrestored cars after 50+ years will no doubt not show the proper finish given they were bare steel from the assemblyline. They rusted easily.
Logged
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24628
Re: Correct tie rod sleeves
« Reply #6 on: July 21, 2021, 12:23:31 AM »
Quote from: SCJSTU on July 18, 2021, 10:31:05 PM
Bringing this post back up???anyone have pictures of original ones on a car?

Jan built 351W

Mustang small suspension tie rod sleeve on a PS 351W Mustang

Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)
Pages: [1]   Go Up
« previous next »